A Guide to Forklift Gates
Forklift and pedestrian crossing gates manage the points where employee walkways intersect with forklift lanes. In warehouses, distribution centers and manufacturing plants, these crossings often sit beside rack ends, production entrances, packing stations or shipping aisles. An automated crossing gives workers and drivers a designated place to wait and a consistent sequence for taking turns through the intersection.
Two decisions determine the configuration. Gate count determines which approaches receive gate arms. Traffic priority determines which traffic stream the system is configured to favor. Make both decisions for the individual crossing, since the best setup for a shift-change walkway may differ from the best setup for a main forklift aisle.
Two Gates vs. Four Gates
A two-gate system places one motorized pedestrian gate on each side of the forklift aisle. The gates control access from both ends of the crosswalk. Forklift operators follow the crossing signals and site procedures, and the system has no dedicated vehicle boom arms.
A four-gate system adds two motorized vehicle boom arms, one on each forklift approach. The controller coordinates the pedestrian gates and vehicle arms so each traffic stream receives a clear visual indication of when to wait. The four-gate layout is worth evaluating where both approaches need a gate indication or where sight lines make it difficult for drivers to see the opposite side of the crossing. The arms serve as traffic-control devices. Where the site assessment calls for physical vehicle restraint, specify impact-rated protection separately.
Compare the Four OnlineRiver Configurations
| Configuration | Gate layout | Crossing operation |
|---|---|---|
| Four Gates, Pedestrian Priority | Two pedestrian gates and two forklift boom arms | Pedestrian gates normally stand open and vehicle arms are lowered. The forklift operator requests passage by pull cord. After the system detects no pedestrian movement, it closes the pedestrian gates and raises the vehicle arms. |
| Two Gates, Pedestrian Priority | Two pedestrian gates | Designed for pedestrian-priority operation with a forklift request via pull cord. Confirm the idle gate positions and exact release sequence against the approved operating drawings. |
| Four Gates, Forklift Priority | Two pedestrian gates and two forklift boom arms | Vehicle arms normally stand raised and pedestrian gates are closed. A pedestrian requests passage by push button. After the system detects no vehicle movement, it lowers the vehicle arms and opens the pedestrian gates. |
| Two Gates, Forklift Priority | Two pedestrian gates | Pedestrian gates normally stand closed. A pedestrian presses the request button, and the gates remain closed until the detection zone is clear of detected vehicle traffic. |
How to Choose Traffic Priority
Pedestrian priority is typically the starting point for a busy employee walkway crossed intermittently by forklifts. Examples include a marked route between production areas or a walkway that fills during shift changes. Evaluate where drivers would wait for the crossing to clear and whether a stopped forklift and its load could obstruct another aisle or work area.
Forklift priority is typically the starting point for a main material-handling aisle with frequent forklift trips and occasional pedestrian crossings. Evaluate where pedestrians will wait, how long a gap in forklift traffic normally takes to occur, and whether the waiting area has room for a group without spilling into the aisle. Observe the crossing during peak traffic as well as normal operations.
Priority describes the gate sequence. Drivers and pedestrians must follow the facility’s crossing procedures and verify the path is clear before entering.
What to Confirm Before Specifying a Crossing
- Approach geometry. Record aisle width, pedestrian opening width, forklift turning paths, load overhang and the clearance needed for moving gate arms. Four-gate layouts also need room for the vehicle cabinets and overhead clearance for raised booms.
- Detection coverage. Review where vehicles approach from both directions and where pedestrians can enter or remain in the crosswalk. During commissioning, verify coverage with the forklifts, loads and pedestrian travel patterns actually present at the site.
- Waiting areas and sight lines. Give each traffic stream a designated place to wait clear of the other route. Check visibility around rack ends, columns, staged pallets and doors.
- Controls and emergency operation. Confirm gate positions at idle, the request and release sequence, warning lights and audible signals, and behavior during an alarm or power interruption. Review electrical requirements and maintain required egress.
- Traffic separation. Use marked walkways and appropriate guardrails to guide people to the crossing. OSHA recommends separating forklift and pedestrian traffic where practical. Its powered industrial truck standard requires drivers to slow down and sound the horn at cross aisles and other locations where vision is obstructed.
For help selecting a system, send OnlineRiver a floor plan or sketch showing the crossing, the clear aisle width, the direction of forklift travel and the busiest pedestrian periods. Include any nearby doors, rack ends or overhead obstructions that could affect gate placement or sensor coverage.
